Results 1 to 1 of 1
  1. #1
    Super JK Freak HSKR4X4's Avatar
    Join Date
    12-27-2011
    Location
    Big Beach No Water
    Posts
    1,916

    Jeep TJ Superchips Jammer CAI Write-Up

    Superchips Jammer CAI
    97-06 4.0 Motors



    Information on Jammer CAI

    The Jammer intake system for the TJ Wrangler adds 8hp and 12lb-ft of torque. The kit outflows the factory intake by 97%! This air intake system features a washable/reusable conical air filter that improves airflow for increased horsepower and torque. The Jammer kit includes a one-piece heat shield that requires no assembly and the filter is constructed with 100% polyurethane for long life and multiple cleaning cycles.

    About Superchips

    Superchips of Sanford, Florida is the industry leader in automotive tuning for late model cars, Jeeps and trucks. Founded in England in 1983, Superchips was one of the first companies to specialize in tuning vehicles with computer controlled fuel-injection systems. While Superchips originally focused on serving the British racing community with high-end solutions, the Company eventually began to provide power to performance enthusiasts throughout the world. Now, Superchips sells tens of thousands of hand-held programmers per year from its headquarters in Ogden, Utah. In 2005, Superchips was acquired by MSD Performance. In 2011 Superchips became part of Powerteq LLC, which today owns and manages the Edge Products and Diablosport brands – two of the most popular performance tuning brands in North America. In 2015, Powerteq LLC, along with the other MSD Performance Group brands, was acquired by the Holley Performance Group. The deep line of Holley brands marries tremendous technology with cutting-edge resources and industry roots. The combination of talented personnel at Powerteq and the resources of Holley Performance Group ensure that exciting aftermarket products will launch from Superchips for many years to come.

    Warranty

    Comes with 1 year warranty from EGT to intake filter

    Price

    $299.95 on superchips.com
    $290-$295 licensed dealers

    Install Time & Install Difficulty

    Install Time- 45 min to 2 hours
    Install Difficulty 1 of 5 Wrenches (5 being hardest)

    What Comes In Kit

    Air Filter
    Housing
    Intake Tube
    Coupling Hump
    Coupling Straight
    Mini Clamp #008 (2)
    Clamp #048 (2)
    Clamp #052 (2)
    Grommet
    M6 Hex Screws (2)
    M6 Wavy Washers (2)
    M6 Hex Nuts (2)
    Fender Washers (4)
    Rubber Grommet Trim
    Cap
    12” Fuel Hose (Breather Hose)

    Tools Needed

    **Only use socket set to help prevent overtightening of parts**

    Socket Wratchet Wrench
    Socket Extension
    8mm Socket
    10mm Socket
    13mm Socket
    Flat Head Screwdriver
    10mm Wrench
    Razor Blade
    Favorite Cold Beverage
    Towels



    Install Guide


    Step 1

    Remove negative cable on battery

    Open hood and prop hood with hood prop. It’s easiest to open hood all the way back, place folded towel and windshield channel and let hood rest folded back.
    Check for (–) sign on battery but 99% of time it’s the black cable going to battery.
    Use socket wrench and 10mm socket to remove.
    Once removed, place negative cable away from positive side cable and let rest on a folded towel.





    Step 2

    Remove factory intake tube

    Remove temp sensor if your Jeep is equipped. Push in on harness adapter then pull towards you with light force disconnecting harness from temp sensor. At this time don’t remove temp sensor from intake.
    Loosen all clamps on intake tube using flat head screw driver.
    Once clamps are loosened, remove intake tube and cover throttle body with clean towel.









    Step 2.5

    Remove factory air box

    Remove vent hose.
    Open air box by flipping back the 5 clamps.
    Remove filter and under filter there are 8mm bolts to remove. (Instructions say 10mm). Use socket wrench, socket extension and 8mm/10mm socket to move upper filter side. Look in upper inner fender and you will see the 3 nuts that attach to these bolts. Use 8mm/10mm wrench to hold nut in place while removing filter side bolts.







    Your factory intake should now be removed!

    Step 3

    Remove strut rod on passenger side of Jeep

    Use socket wrench and 13mm bolt to remove.
    Once removed slide on the supplied rubber grommet that comes in the Superchips Jammer CAI kit.





    Step 4

    Install Jammer CAI air box

    Remove upper radiator bolt using socket wrench, extension and 10mm socket to remove. Keep bolt to side as you will be reusing.
    Slide strut bar through back hole of air box, sit air box where factory air box was, and tighten down fire wall side of strut bar using socket wrench and 13mm socket.
    Line up air box to factory holes and loosely fit the upper radiator bolt and lower 3 bolts.
    Once everything is loosely fit, tighten down upper radiator bolt, then strut bar, then the 3 lower bolts using the supplies bolt, washers and nuts.
    Radiator bolt 10mm socket. Strut bar 13mm. Lower air box 10mm socket and wrench.







    Step 4.5

    Install Jammer CAI Intake Tube and Filter

    Slide 2 clamps onto each side of intake.
    Install “straight” coupler onto throttle body side of intake and “” onto air box side of intake.
    Install intake tube into air box side first them remove towel off throttle body and slide intake tube into place. Once intake tube is adjusted and fit properly into place, tighten clamps using flat head screw driver. DON’T USE SOCKET-DON’T OVER TIGHTEN.
    Reinstall new provided vent hose into place, remove hose, cut access length off, slide provided clamps onto hose, then reinstall using flat head or Philips screw driver and tighten down. DON’T USE SOCKET-DON’T OVER TIGHTEN.
    Slide last provided clamp onto Jammer CAI intake filter then slide into place on air box and tighten with flat head screw driver.
    Install provided Jammer CAI information sticker in a noticeable area on air box. Without the sticker, most inspection places won’t pass you without it.











    Step 5

    SKIP THIS STEP IF YOU DON’T HAVE AIR TEMP SENSOR

    Remove air temp sensor cap on the intake and twist off your air temp sensor from old intake tube and slide through grommet where cap was. Hold back of intake tube to keep from over forcing air temp sensor into place. I do recommend replacing the worn out air temp sensor with new. New runs about $11 from any auto store so it not anything overly expensive.






    Congratulations!!!! Your new Superchips Jammer CAI Intake is now installed!

    Look over your work and make sure all clamps, bolts and hardware are tightened down, remove towel under negative cable, and properly install negative cable using socket wrench and 10mm socket. After 100-200 miles check all hardware making sure nothing has come loose!

    Last edited by HSKR4X4; 09-06-2018 at 12:37 PM.
    GO BIG RED!
    PABST BLUE RIBBON!

    My build page
    https://www.facebook.com/husker4x4

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •