Results 1 to 4 of 4
  1. #1
    New JK Freak
    Join Date
    08-20-2016
    Location
    Virginia
    Posts
    9

    Pinion bearing help

    13 jk danna 30

    need help anyone know part numbers for both the pinion bearings the inner and outer bearing thanks Iím running a arb locker so donít wanna buy a full rebuild kit


    Sent from my iPhone using Tapatalk

  2. #2
    Supporting Freak bradm's Avatar
    Join Date
    05-04-2012
    Location
    Delaware, Ohio
    Posts
    1,118
    d30 inner pinion bearing cone: http://amzn.to/2FT7MK4

    d30 inner pinion bearing race: http://amzn.to/2GcYM1C

    d30 outer pinion bearing cone: http://amzn.to/2ufjQzV

    d30 outer pinion bearing race: http://amzn.to/2GPdmdD

    d30 pinion seal: http://amzn.to/2ptcRyp

    d30 pinion depth shim kit: http://amzn.to/2HS5GXk

    I did a rebuild/regear on my original 30 last spring when I sold it to replace it with a 44. I shopped around everywhere looking for all of the components and those were the best prices I could find. FYI - those are my amazon affiliate links. They get me a very small referral incentive, but there is no price hike to you at all. You still see the same everyday amazon price. If you're not comfortable with that, you can always search the part numbers separately and find the item without the referral part.
    Last edited by bradm; 03-21-2018 at 08:23 AM.
    2011 Black Sahara Unlimited
    4" FrankenLift
    37" MTR/Ks on black 17" ProComps
    DIY Hydro-Assist Steering
    Rubicon front axle with Yukon 5.13's
    Rear Eaton E-Locker with Yukon 5.13's

  3. #3
    New JK Freak
    Join Date
    08-20-2016
    Location
    Virginia
    Posts
    9
    Thanks u sir now to remember my log in


    Sent from my iPhone using Tapatalk

  4. #4
    Supporting Freak bradm's Avatar
    Join Date
    05-04-2012
    Location
    Delaware, Ohio
    Posts
    1,118
    You're welcome.

    Almost forgot - you need a new pinion nut too. Those are not reusable - they'll back off. You can use the old nut when you're setting up preload and pinion depth, since that will likely take several on-and-off cycles to dial it in. Then use the new nut when all that is set and you're ready for final install.

    pinion nut: http://amzn.to/2Gb0PDf

    You also can't reuse the crush sleeve. I don't have a link handy for that part because i used a crush-sleeve eliminator kit from Yukon when I built my new 44 and when I regeared the 30. It is way more forgiving for someone that doesn't build axles every other day. If you want to go that route, here is the best price I could find last year during the build-up: https://www.walmart.com/ip/Crush-sle...JK-F/196709867
    2011 Black Sahara Unlimited
    4" FrankenLift
    37" MTR/Ks on black 17" ProComps
    DIY Hydro-Assist Steering
    Rubicon front axle with Yukon 5.13's
    Rear Eaton E-Locker with Yukon 5.13's

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •